TI,TI公司,TI代理商
TI(德州仪器)| TI产品型号搜索
专营TI元器件,强大的现货交付能力,解决您的采购难题
全流程提供TI现货供应链服务
当前位置:TI公司 > > TI芯片 >> PCA9515A
PCA9515A技术文档下载:
PCA9515A技术文档产品手册下载
PCA9515A - 产品图解:
PCA9515A-双路双向 I2C 总线和 SMBus 中继器
承诺原装正品
专营TI,真正优化您的供应链
TI产品 - PCA9515A介绍
PCA9515A - 双路双向 I2C 总线和 SMBus 中继器

PCA9515A是TI公司的一款I2C集线器、缓冲器、中继器产品,PCA9515A是双路双向 I2C 总线和 SMBus 中继器,本页介绍了PCA9515A的产品说明、应用、特性等,并给出了与PCA9515A相关的TI元器件型号供参考。

PCA9515A - 双路双向 I2C 总线和 SMBus 中继器 - I2C集线器、缓冲器、中继器 - I2C - TI公司(Texas Instruments,德州仪器)

产品描述

This dual bidirectional I2C buffer is operational at 2.3-V to 3.6-V VCC.

The PCA9515A is a BiCMOS integrated circuit intended for I2C bus and SMBus systems applications. The device contains two identical bidirectional open-drain buffer circuits that enable I2C and similar bus systems to be extended without degradation of system performance.

The PCA9515A buffers both the serial data (SDA) and serial clock (SCL) signals on the I2C bus, while retaining all the operating modes and features of the I2C system. This enables two buses of 400-pF bus capacitance to be connected in an I2C application.

The I2C bus capacitance limit of 400pF restricts the number of devices and bus length. Using the PCA9515A enables the system designer to isolate two halves of a bus, accommodating more I2C devices or longer trace lengths.

The PCA9515A has an active-high enable (EN) input with an internal pullup, which allows the user to select when the repeater is active. This can be used to isolate a badly behaved slave on power-up reset. It never should change state during an I2C operation, because disabling during a bus operation hangs the bus, and enabling part way through a bus cycle could confuse the I2C parts being enabled. The EN input should change state only when the global bus and the repeater port are in an idle state, to prevent system failures.

The PCA9515A also can be used to run two buses: one at 5-V interface levels and the other at 3.3-V interface levels, or one at 400-kHz operating frequency and the other at 100-kHz operating frequency. If the two buses are operating at different frequencies, the 100-kHz bus must be isolated when the 400-kHz operation of the other bus is required. If the master is running at 400kHz, the maximum system operating frequency may be less than 400kHz, because of the delays that are added by the repeater.

The PCA9515A does not support clock stretching across the repeater.

The output low levels for each internal buffer are approximately 0.5V, but the input voltage of each internal buffer must be 70mV or more below the output low level, when the output internally is driven low. This prevents a lockup condition from occurring when the input low condition is released.

Two or more PCA9515A devices cannot be used in series. The PCA9515A design does not allow this configuration. Because there is no direction pin, slightly different valid low-voltage levels are used to avoid lockup conditions between the input and the output of each repeater. A valid low applied at the input of a PCA9515A is propagated as a buffered low with a slightly higher value on the enabled outputs. When this buffered low is applied to another PCA9515A-type device in series, the second device does not recognize it as a valid low and does not propagate it as a buffered low again.

The device contains a power-up control circuit that sets an internal latch to prevent the output circuits from becoming active until VCC is at a valid level (VCC = 2.3 V).

As with the standard I2C system, pullup resistors are required to provide the logic high levels on the buffered bus. The PCA9515A has standard open-collector configuration of the I2C bus. The size of these pullup resistors depends on the system, but each side of the repeater must have a pullup resistor. The device is designed to work with StandardMode and FastMode I2C devices in addition to SMBus devices. StandardMode I2C devices only specify 3mA in a generic I2C system where StandardMode devices and multiple masters are possible. Under certain conditions, high termination currents can be used.

产品特性

  • Two-Channel Bidirectional Buffers
  • I2C Bus and SMBus Compatible
  • Active-High Repeater-Enable Input
  • Open-Drain I2C I/O
  • 5.5-V Tolerant I2C I/O and Enable Input Support Mixed-Mode Signal Operation
  • Lockup-Free Operation
  • Accommodates Standard Mode and Fast Mode I2C Devices and Multiple Masters
  • Powered-Off High-Impedance I2C Pins
  • Latch-Up Performance Exceeds 100 mA Per JESD 78, Class II
  • ESD Protection Exceeds JESD 22
    • 2000-V Human-Body Model (A114-A)
    • 200-V Machine Model (A115-A)
    • 1000-V Charged-Device Model (C101)

下面可能是您感兴趣的TI公司I2C集线器、缓冲器、中继器元器件
  • SN75HVD08 - 3.3/5V RS-485 收发器
  • SN65HVD1176 - PROFIBUS RS-485 收发器
  • ADS1198 - 用于 ECG/EEG 测量的低噪声、8 通道、16 位模拟前端
  • TPS75425 - 单输出 LDO、2.0A、固定电压 (2.5V)、电源良好 (PG) 输出、快速瞬态响应
  • DRV8302 - 具有双路电流感应放大器和降压转换器的三相无刷电机前 置驱动器(PWM 控制器)
  • CD4035B-MIL - CMOS 4 级并行输入/并行输出移位寄存器
  • TPS7A3001-EP - 增强型产品,-3V 至 -36V 输入电压、-200mA、超低噪声、高 PSRR、低压降线性稳压器
  • CSD13381F4 - 12V N 通道 NexFET? 功率 MOSFET,CSD13381F4
  • SN74AHC74-EP - 具有清零和预设功能的增强型产品双路上升沿 D 类触发器
  • CD40174B-MIL - CMOS 六路 D 类触发器
  • 节约时间成本,提高采购效率,TI官网授权代理
    TI公司|TI德州仪器|德州仪器TI公司代理商|TI芯片代理商
    TI公司产品现货专家,订购TI公司产品不限最低起订量,TI产品大陆现货即时发货,香港库存3-5天发货,海外库存7-10天发货
    寻找全球TI代理商现货货源 - TI公司(德州仪器)电子元件在线订购