74SSTUB32864A - 25-Bit Configurable Registered Buffer w/Address-Parity Test

74SSTUB32864A是TI德州仪器公司的一款DDR2寄存器产品，74SSTUB32864A是25-Bit Configurable Registered Buffer w/Address-Parity Test，本站介绍了74SSTUB32864A的封装应用图解、特点和优点、功能等，并给出了与74SSTUB32864A相关的TI元器件型号供参考。

74SSTUB32864A - 25-Bit Configurable Registered Buffer w/Address-Parity Test - DDR2寄存器 - 存储器接口时钟和寄存器 - 德州仪器

产品描述

This 25-bit 1:1 or 14-bit 1:2 configurable registered buffer is designed for 1.7-V to 1.9-V VCC operation. In the1:1 pinout configuration, only one device per DIMM is required to drive nine SDRAM loads. In the 1:2 pinout configuration, two devices per DIMM are required to drive 18 SDRAM loads.

All inputs are SSTL_18, except the reset (RESET) and control (Cn) inputs, which are LVCMOS. All outputs are edge-controlled circuits optimized for unterminated DIMM loads and meet SSTL_18 specifications, except the open-drain error (QERR) output.

The 74SSTUB32864A operates from a differential clock (CLK and CLK). Data are registered at the crossing of CLK going high and CLK going low.

The C0 input controls the pinout configuration of the 1:2 pinout from register-A configuration (when low) to register-B configuration (when high). The C1 input controls the pinout configuration from 25-bit 1:1 (when low) to 14-bit 1:2 (when high). C0 and C1 should not be switched during normal operation. They should be hard-wired to a valid low or high level to configure the register in the desired mode. In the 25-bit 1:1 pinout configuration, the A6, D6, and H6 terminals are driven low and are do-not-use (DNU) pins.

In the DDR2 RDIMM application, RESET is specified to be completely asynchronous with respect to CLK and CLK. Therefore, no timing relationship can be ensured between the two. When entering reset, the register is cleared, and the data outputs are driven low quickly, relative to the time required to disable the differential input receivers. However, when coming out of reset, the register becomes active quickly, relative to the time required to enable the differential input receivers. As long as the data inputs are low, and the clock is stable during the time from the low-to-high transition of RESET until the input receivers are fully enabled, the design of the 74SSTUB32864A ensures that the outputs remain low, thus ensuring there will be no glitches on the output.

To ensure defined outputs from the register before a stable clock has been supplied, RESET must be held in the low state during power up.

The device supports low-power standby operation. When RESET is low, the differential input receivers are disabled, and undriven (floating) data, clock, and reference voltage (VREF) inputs are allowed. In addition, when RESET is low, all registers are reset and all outputs are forced low. The LVCMOS RESET and Cn inputs always must be held at a valid logic high or low level.

The device also supports low-power active operation by monitoring both system chip select (DCS and CSR) inputs and gates the Qn outputs from changing states when both DCS and CSR inputs are high. If either DCS or CSR input is low, the Qn outputs function normally. The RESET input has priority over the DCS and CSR control and, when driven low, forces the Qn outputs low. If the DCS control functionality is not desired, the CSR input can be hard-wired to ground, in which case the setup-time requirement for DCS is the same as for the other D data inputs. To control the low-power mode with DCS only, the CSR input should be pulled up to VCC through a pullup resistor.

The two VREF pins (A3 and T3) are connected together internally by approximately 150. However, it is necessary to connect only one of the two VREF pins to the external VREF power supply. An unused VREF pin should be terminated with a VREF coupling capacitor.

产品特性

Member of the Texas InstrumentsWidebus+™ Family
Pinout Optimizes DDR2 DIMM PCB Layout
Configurable as 25-Bit 1:1 or 14-Bit 1:2 Registered Buffer
Chip-Select Inputs Gate the Data Outputs from Changing State and Minimizes System Power Consumption
Output Edge-Control Circuitry Minimizes Switching Noise in an Unterminated Line
Supports SSTL_18 Data Inputs
Differential Clock (CLK and CLK) Inputs
Supports LVCMOS Switching Levels on the Control and RESET Inputs
RESET Input Disables Differential Input Receivers, Resets All Registers, and Forces All Outputs Low

Widebus+ is a trademark of Texas Instruments.

下面可能是您感兴趣的TI德州仪器公司DDR2寄存器元器件

TI公司产品现货专家，订购TI公司产品不限最低起订量，TI芯片大陆现货即时发货，香港库存3-5天发货，海外库存7-10天发货

寻找全球TI代理商现货货源 - TI公司（德州仪器）电子元件在线订购