CD40117B - 可编程双路 4 位终端 (20V 额定)

CD40117B是TI德州仪器公司的一款总线终端阵列/网络产品，CD40117B是可编程双路 4 位终端 (20V 额定)，本站介绍了CD40117B的封装应用图解、特点和优点、功能等，并给出了与CD40117B相关的TI元器件型号供参考。

CD40117B - 可编程双路 4 位终端 (20V 额定) - 总线终端阵列/网络 - 特殊逻辑 - 德州仪器

产品描述

CD40117B is a dual 4-bit terminator that can be programmed by means of STROBE and DATA control bits to function as pull-up or pull-down resistors. The CD40117B can also be programmed to function as latches to terminate any open or unused CMOS logic when used with 3-state logic or during a power-down condition. Considerable savings in power and board space can be realized when this device is used to replace pull-up or pull-down resistors. When the STROBE is in the logic "1" state, the terminator functions as a pull-up resistor if the DATA input is a logic "1" or as a pull down resistor if the DATA input is a logic "0".

When the STROBE is in the logic "0" state, the terminator performs the latch functions, i.e., it follows the changing states of the bus. If the bus goes into the high-Z state or into a power-down condition, the latched terminator retains the data ("1" or "0") that the bus carried before it switched to the high-Z or power-down state. If and when the bus changes from the high-Z state to the state opposite to that which the latch is storing, the bus will override the latch and the terminator will reflect the state on the bus. The small geometries chosen for the inverters in the latch allow this override mode. When checking the data bus whose last state is being preserved by the terminator, a resistor should be used in series with the probe whose input capacitance could trip the small latches. The resistance should be in excess of the output impedance of the latch, i.e., R should be > 30 K at VDD = 10 V.

The STROBE and DATA inputs in each section can be paralleled allowing this device to be used as an 8-bit bus terminator.

The CD40117B types are supplied in 14-lead dual-in-line plastic packages (E suffix), 14-lead small-outline packages (M, MT, M96, and NSR suffixes), and 14-lead thin shrink small-outline packages (PW and PWR suffixes).

产品特性

One standard "B" output will drive eight terminator circuits.
Will terminate a CMOS data bus with up to 40 B-series inputs inputs or 3-state outputs connected at VDD of 5 V.
Input terminal protected by standard "B" series ESD protection network.
Preserves final logic state.
Output after switching is closer to VDD or VSS rail than with a resistor.
Requires only one solder connection.
Open circuited terminator not used will not affect performance.
Can be connected to any CMOS I/O line.
Draws current only when logic state is changing.
Can be preset.
Applications
- Error state identification.
- Replaces pull-up or pull-down resistors
- Avoids floating inputs in modular systems
- Sharpens transistors (hysteresis)
- Anti-bounce circuit

NOT RECOMMENDED FOR NEW DESIGNS

下面可能是您感兴趣的TI德州仪器公司总线终端阵列/网络元器件

TI公司产品现货专家，订购TI公司产品不限最低起订量，TI芯片大陆现货即时发货，香港库存3-5天发货，海外库存7-10天发货

寻找全球TI代理商现货货源 - TI公司（德州仪器）电子元件在线订购