MAX3238E - 具有 +/-15kV ESD (HBM) 保护的 3V 至 5.5V 多通道 RS-232 线路驱动器/接收器

MAX3238E是TI德州仪器公司的一款无产品，MAX3238E是具有 +/-15kV ESD (HBM) 保护的 3V 至 5.5V 多通道 RS-232 线路驱动器/接收器，本站介绍了MAX3238E的封装应用图解、特点和优点、功能等，并给出了与MAX3238E相关的TI元器件型号供参考。

MAX3238E - 具有 +/-15kV ESD (HBM) 保护的 3V 至 5.5V 多通道 RS-232 线路驱动器/接收器 - 无 - RS-232收发器 - 德州仪器

产品描述

产品特性

RS-232 Bus-Pin ESD Protection Exceeds ±15 kV Using Human-Body Model (HBM)
Meets or Exceeds the Requirements of TIA/EIA-232-F and ITU v.28 Standards
Operates With 3-V to 5.5-V VCC Supply
Operates up to 400 kbit/s
Five Drivers and Three Receivers
Auto-Powerdown Plus Feature Enables Flexible Power-Down Mode
Low Standby Current . . . 1 µA Typical
External Capacitors . . . 4 × 0.1 µF
Accepts 5-V Logic Input With 3.3-V Supply
Always-Active Noninverting Receiver Output (ROUT1B)
Alternative High-Speed Pin-Compatible Device (1 Mbit/s) for SNx5C3238
ESD Protection for RS-232 Interface Pins
- ±15 kV - Human-Body Model (HBM)
- ±8 kV - IEC61000-4-2, Contact Discharge
- ±15 kV - IEC61000-4-2, Air-Gap Discharge
APPLICATIONS
- Battery-Powered Systems
- PDAs
- Notebooks
- Subnotebooks
- Laptops
- Palmtop PCs
- Hand-Held Equipment
- Modems
- Printers

DESCRIPTION/ORDERING INFORMATION

The MAX3238E consists of five line drivers, three line receivers, and a dual charge-pump circuit with ±15-kV ESD (HBM) protection on the driver output (DOUT) and receiver input (RIN) terminals. The device meets the requirements of TIA/EIA-232-F and provides the electrical interface between notebook and subnotebook computer applications. The charge pump and four small external capacitors allow operation from a single 3-V to 5.5-V supply. In addition, the device includes an always-active noninverting output (ROUT1B), which allows applications using the ring indicator to transmit data while the device is powered down. This device operates at data signaling rates up to 250 kbit/s and a maximum of 30-V/µs driver output slew rate.

Flexible control options for power management are featured when the serial port and driver inputs are inactive. The auto-powerdown plus feature functions when FORCEON is low and FORCEOFF is high. During this mode of operation, if the device does not sense valid signal transitions on all receiver and driver inputs for approximately 30 s, the built-in charge pump and drivers are powered down, reducing the supply current to 1 µA. By disconnecting the serial port or placing the peripheral drivers off, auto-powerdown plus occurs if there is no activity in the logic levels for the driver inputs. Auto-powerdown plus can be disabled when FORCEON and FORCEOFF are high. With auto-powerdown plus enabled, the device activates automatically when a valid signal is applied to any receiver or driver input. INVALID is high (valid data) if any receiver input voltage is greater than 2.7 V or less than -2.7 V, or has been between -0.3 V and 0.3 V for less than 30 µs. INVALID is low (invalid data) if all receiver input voltages are between -0.3 V and 0.3 V for more than 30 µs.

下面可能是您感兴趣的TI德州仪器公司无元器件

TI公司产品现货专家，订购TI公司产品不限最低起订量，TI芯片大陆现货即时发货，香港库存3-5天发货，海外库存7-10天发货

寻找全球TI代理商现货货源 - TI公司（德州仪器）电子元件在线订购