The SN74CB3T16211 is a high-speed TTL-compatible FET bus switch with low ON-state resistance (ron), allowing for minimal propagation delay. The device fully supports mixed-mode signal operation on all data I/O ports by providing voltage translation that tracks VCC. The SN74CB3T16211 supports systems using 5-V TTL, 3.3-V LVTTL, and 2.5-V CMOS switching standards, as well as user-defined switching levels.

The I/O port of this device has a pullup current source that maintains the output voltage at VCC when the device is ON, and the input is greater than or equal to VCC – 1. Because of the pullup current source, the output voltage level may be less than VCC when the operating frequency is low and the I/O port is connected to a pulldown resistor. In order to maintain the output voltage at VCC, a pullup resistor must be connected to VCC instead of a pulldown resistor to ground.

The SN74CB3T16211 is organized as two 12-bit bus switches with separate output-enable (1OE, 2OE) inputs. It can be used as two 12-bit bus switches or as one 24-bit bus switch. When OE is low, the associated 12-bit bus switch is ON, and the A port is connected to the B port, allowing bidirectional data flow between ports. When OE is high, the associated 12-bit bus switch is OFF, and a high-impedance state exists between the A and B ports.

This device is fully specified for partial-power-down applications using Ioff. The Ioff feature ensures that damaging current will not backflow through the device when it is powered down. The device has isolation during power off.

To ensure the high-impedance state during power up or power down, OE should be tied to VCC through a pullup resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver.

• Member of the Texas Instruments Widebus Family
• Output Voltage Translation Tracks VCC
• Supports Mixed-Mode Signal Operation on All Data I/O Ports
  • 5-V Input Down to 3.3-V Output Level Shift With 3.3-V VCC
  • 5-V/3.3-V Input Down to 2.5-V Output Level Shift With 2.5-V VCC
• 5-V Tolerant I/Os With Device Powered Up or Powered Down
• Bidirectional Data Flow With Near-Zero Propagation Delay
• Low ON-State Resistance (ron) Characteristics (ron = 5 Ω Typ)
• Low Input/Output Capacitance Minimizes Loading (Cio(OFF) = 5 pF Typ)
• Data and Control Inputs Provide Undershoot Clamp Diodes
• Low Power Consumption (ICC = 70 µA Max)
• VCC Operating Range From 2.3 V to 3.6 V
• Data I/Os Support 0- to 5-V Signaling Levels (0.8 V, 1.2 V, 1.5 V, 1.8 V, 2.5 V, 3.3 V, 5 V)
• Control Inputs Can Be Driven by TTL or 5-V/3.3-V CMOS Outputs
• Ioff Supports Partial-Power-Down Mode Operation
• Latch-Up Performance Exceeds 250 mA Per JESD 17
• ESD Performance Tested Per JESD 22
  • 2000-V Human-Body Model (A114-B, Class II)
  • 1000-V Charged-Device Model (C101)
• Supports Digital Applications: Level Translation, PCI Interface, Bus Isolation
• Ideal for Low-Power Portable Equipment

• UC1843 - 电流模式 PWM 控制器
• CD4572UB - CMOS 六个门（具有 4 个反向器、1 个 2 输入或非门和 1 个 2 输入与非门）
• SN74ACT374 - 具有三态输出的八路 D 类边沿触发器
• SN74AHC595 - 具有三态输出寄存器的 8 位移位寄存器
• SN74LVC1G57 - 可配置多功能门
• CD74HC280 - 高速 CMOS 逻辑 9 位奇偶校验发生器/校验器
• DS26C32AMQML - CMOS Quad Differential Line Receivers
• UC2854BM - 增强型高功率因子前置稳压器
• SN65HVD77 - 3.3V 电源 RS-485
• LM22678-Q1 - 具有精密启用的 5A SIMPLE SWITCHER，降压电压稳压器