The SN74GTLP2033 is a high-drive, 8-bit, three-wire registered transceiver that provides inverted LVTTL-to-GTLP and GTLP-to-LVTTL signal-level translation. The device allows for transparent, latched, and flip-flop modes of data transfer with separate LVTTL input and LVTTL output pins, which provides a feedback path for control and diagnostics monitoring, the same functionality as the SN74FB2033. The device provides a high-speed interface between cards operating at LVTTL logic levels and a backplane operating at GTLP signal levels. High-speed (about three times faster than standard LVTTL or TTL) backplane operation is a direct result of GTLP's reduced output swing (<1 V), reduced input threshold levels, improved differential input, OEC™ circuitry, and TI-OPC™ circuitry. Improved GTLP OEC and TI-OPC circuits minimize bus-settling time and have been designed and tested using several backplane models. The high drive allows incident-wave switching in heavily loaded backplanes with equivalent load impedance down to 11 .

GTLP is the Texas Instruments derivative of the Gunning Transceiver Logic (GTL) JEDEC standard JESD 8-3. The ac specification of the SN74GTLP2033 is given only at the preferred higher noise-margin GTLP, but the user has the flexibility of using this device at either GTL (VTT = 1.2 V and VREF = 0.8 V) or GTLP (VTT = 1.5 V and VREF = 1 V) signal levels. For information on using GTLP devices in FB+/BTL applications, refer to TI application reports, Texas Instruments GTLP Frequently Asked Questions, literature number SCEA019, and GTLP in BTL Applications, literature number SCEA017.

Normally, the B port operates at GTLP signal levels. The A-port and control inputs operate at LVTTL logic levels, but are 5-V tolerant and can be directly driven by TTL or 5-V CMOS devices. VREF is the B-port differential input reference voltage.

This device is fully specified for live-insertion applications using Ioff, power-up 3-state, and BIAS VCC. The Ioff circuitry disables the outputs, preventing damaging current backflow through the device when it is powered down. The power-up 3-state circuitry places the outputs in the high-impedance state during power up and power down, which prevents driver conflict. The BIAS VCC circuitry precharges and preconditions the B-port input/output connections, preventing disturbance of active data on the backplane during card insertion or removal, and permits true live-insertion capability.

This GTLP device features TI-OPC circuitry, which actively limits overshoot caused by improperly terminated backplanes, unevenly distributed cards, or empty slots during low-to-high signal transitions. This improves signal integrity, which allows adequate noise margin to be maintained at higher frequencies.

High-drive GTLP backplane interface devices feature adjustable edge-rate control (ERC). Changing the ERC input voltage between low and high adjusts the B-port output rise and fall times.This allows the designer to optimize system data-transfer rate and signal integrity to the backplane load.

When VCC is between 0 and 1.5 V, the device is in the high-impedance state during power up or power down. However, to ensure the high-impedance state above 1.5 V, OEAB\ should be tied to VCC through a pullup resistor and OEAB and OEBA should be tied to GND through a pulldown resistor; the minimum value of the resistor is determined by the current-sinking/current-sourcing capability of the driver.

• Member of the Texas Instruments Widebus™ Family
• TI-OPC™ Circuitry Limits Ringing on Unevenly Loaded Backplanes
• OEC™ Circuitry Improves Signals Integrity and Reduces Electromagnetic Interference
• Bidirectional Interface Between GTLP Signal Levels and LVTTL Logic Levels
• Split LVTTL Port Provides a Feedback Path for Control and Diagnostics Monitoring
• LVTTL Interfaces Are 5-V Tolerant
• High-Drive GTLP Open-Drain Outputs (100 mA)
• LVTTL Outputs (\x9624 mA/24 mA)
• Variable Edge-Rate Control (ERC) Input Selects GTLP Rise and Fall Times for Optimal Data-Transfer Rate and Signal Integrity in Distributed Loads
• Ioff, Power-Up 3-State, and BIAS VCC Support Live Insertion
• Distributed VCC and GND Pins Minimize
High-Speed Switching Noise
• Latch-Up Performance Exceeds 100 mA Per JESD 78, Class II
• ESD Protection Exceeds JESD 22
  • 2000-V Human-Body Model (A114-A)
  • 1000-V Charged-Device Model (C101)

OEC, TI-OPC, and Widebus are trademarks of Texas Instruments.

• MSP432P401R - MSP432P4xx：Falcon 系列
• TPS65124 - 具有可调节定序的 3 通道单电感器多路输出 (SIMO) 偏置 IC
• LM3553 - 具有 I2C 兼容接口的 1.2A 双闪存 LED 驱动器系统
• TPD4S010 - 用于高速差分接口的 4 通道 ESD 解决方案
• SN74F283 - 具有快速进位的 4 位二进制全加器
• LM3241 - 6MHz, 750mA Miniature, Adjustable, Step-Down DC-DC Converter for RF Power Amplifiers
• SN54LVTH374 - 具有三态输出的八路边沿 D 类触发器
• PCM3060 - 具有 96/192kHz 采样速率的 24 位异步立体声音频编解码器
• ADC3444 - ADC3444 四通道 14 位 125 Msps 模数转换器
• INA226 - 支持报警功能的 36V、双向、超高精度、低侧/高侧、I2C 输出电流/功率监控器