SN74LVCH16T245-EP - 增强型产品 16 位双电源总线收发器，具有可配置电压转换和三态输出

SN74LVCH16T245-EP是TI德州仪器公司的一款方向控制电压转换产品，SN74LVCH16T245-EP是增强型产品 16 位双电源总线收发器，具有可配置电压转换和三态输出，本站介绍了SN74LVCH16T245-EP的封装应用图解、特点和优点、功能等，并给出了与SN74LVCH16T245-EP相关的TI元器件型号供参考。

SN74LVCH16T245-EP - 增强型产品 16 位双电源总线收发器，具有可配置电压转换和三态输出 - 方向控制电压转换 - 电压电平转换 - 德州仪器

产品描述

This 16-bit noninverting bus transceiver uses two separate configurable power-supply rails. The A port is designed to track VCCA. VCCA accepts any supply voltage from 1.65 V to 5.5 V. The B port is designed to track VCCB. VCCB accepts any supply voltage from 1.65 V to 5.5 V. This allows for universal low-voltage bidirectional translation between any of the 1.8-V, 2.5-V, 3.3-V, and 5-V voltage nodes.

The SN74LVCH16T245 is designed so that the control pins (1DIR, 2DIR, 1OE, and 2OE) are supplied by VCCA.

The SN74LVCH16T245 is designed for asynchronous communication between two data buses. The logic levels of the direction-control (DIR) input and the output-enable (OE) input activate either the B-port outputs or the A-port outputs or place both output ports into the high-impedance mode. The device transmits data from the A bus to the B bus when the B-port outputs are activated, and from the B bus to the A bus when the A-port outputs are activated. The input circuitry on both A and B ports is always active and must have a logic HIGH or LOW level applied to prevent excess ICC and ICCZ.

Active bus-hold circuitry holds unused or undriven data inputs at a valid logic state. Use of pullup or pulldown resistors with the bus-hold circuitry is not recommended.

This device is fully specified for partial-power-down applications using Ioff. The Ioff circuitry disables the outputs, preventing damaging current backflow through the device when it is powered down.

The VCC isolation feature ensures that if either VCC input is at GND, then all outputs are in the high-impedance state. The bus-hold circuitry on the powered-up side always stays active.

To ensure the high-impedance state during power up or power down, OE should be tied to VCC through a pullup resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver.

产品特性

Control Inputs VIH/VIL Levels Are Referenced to VCCA Voltage
VCC Isolation Feature – If Either VCC Input Is at GND, All Outputs Are in the High-Impedance State
Overvoltage-Tolerant Inputs/Outputs Allow Mixed-Voltage-Mode Data Communications
Fully Configurable Dual-Rail Design Allows Each Port to Operate Over the Full 1.65-V to 5.5-V Power-Supply Range
Bus Hold on Data Inputs Eliminates the Need for External Pullup/Pulldown Resistors
Ioff Supports Partial-Power-Down Mode Operation
Latch-Up Performance Exceeds 100 mA Per JESD 78, Class II
ESD Protection Exceeds JESD 22
- 2000-V Human-Body Model (A114-A)
- 200-V Machine Model (A115-A)
- 1000-V Charged-Device Model (C101)

SUPPORTS DEFENSE, AEROSPACE, AND MEDICAL APPLICATIONS

Controlled Baseline
One Assembly/Test Site
One Fabrication Site
Available in Military (–55°C/125°C) Temperature Range(1)
Extended Product Life Cycle
Extended Product-Change Notification
Product Traceability

(1) Custom temperature ranges available

下面可能是您感兴趣的TI德州仪器公司方向控制电压转换元器件

TI公司产品现货专家，订购TI公司产品不限最低起订量，TI芯片大陆现货即时发货，香港库存3-5天发货，海外库存7-10天发货

寻找全球TI代理商现货货源 - TI公司（德州仪器）电子元件在线订购