SN74SSQEA32882 - SSQEA32882 DDR3 寄存器

SN74SSQEA32882是TI德州仪器公司的一款DDR3寄存器产品，SN74SSQEA32882是SSQEA32882 DDR3 寄存器，本站介绍了SN74SSQEA32882的封装应用图解、特点和优点、功能等，并给出了与SN74SSQEA32882相关的TI元器件型号供参考。

SN74SSQEA32882 - SSQEA32882 DDR3 寄存器 - DDR3寄存器 - 存储器接口时钟和寄存器 - 德州仪器

产品描述

This JEDEC SSTE32882-compliant, 28-bit 1:2 or 26-bit 1:2 and 4-bit 1:1 registering clock driver with parity is designed for operation on DDR3 registered DIMMs with VDD of 1.5 V and on DDR3L registered DIMMs with VDD of 1.35 V.

All inputs are 1.5 V and 1.35 V CMOS compatible. All outputs are CMOS drivers optimized to drive DRAM signals on terminated traces in DDR3 RDIMM applications. The clock outputs Yn and Yn and control net outputs DxCKEn, DxCSn and DxODTn can be driven with a different strength and skew to optimize signal integrity, compensate for different loading and equalize signal travel speed.

The SN74SSQEA32882 has two basic modes of operation associated with the Quad Chip Select Enable (QCSEN) input. When the QCSEN input pin is open (or pulled high), the component has two chip select inputs, DCS0 and DCS1, and two copies of each chip select output, QACS0, QACS1, QBCS0 and QBCS1. This is the "QuadCS disabled" mode. When the QCSEN input pin is pulled low, the component has four chip select inputs DCS[3:0], and four chip select outputs, QCS[3:0]. This is the "QuadCS enabled" mode. Through the remainder of this specification, DCS[n:0] will indicate all of the chip select inputs, where n=1 for QuadCS disabled, and n=3 for QuadCS enabled. QxCS[n:0] will indicate all of the chip select outputs.

The device also supports a mode where a single device can be mounted on the back side of a DIMM. If MIRROR=HIGH, Input Bus Termination (IBT) has to stay enabled for all input signals in this case.

The SN74SSQEA32882 operates from a differential clock (CK and CK). Data are registered at the crossing of CK going HIGH, and CK going LOW. This data could be either re-driven to the outputs or it could be used to access device internal control registers.

The input bus data integrity is protected by a parity function. All address and command input signals are added up and the last bit of the sum is compared to the parity signal delivered by the system at the input PAR_IN one clock cycle later. If they do not match the device pulls the open drain output ERROUT LOW. The control signals (DCKE0, DCKE1, DODT0, DODT1, DCS[n:0]) are not part of this computation.

The SN74SSQEA32882 implements different power saving mechanisms to reduce thermal power dissipation and to support system power down states. By disabling unused outputs the power consumption is further reduced.

The package is optimized to support high density DIMMs. By aligning input and output positions towards DIMM finger signal ordering and SDRAM ballout the device de-scrambles the DIMM traces allowing low cross talk design with low interconnect latency.

Edge controlled outputs reduce ringing and improve signal eye opening at the SDRAM inputs.

产品特性

JEDEC SSTE32882 Compliant
1-to-2 Register Outputs and 1-to-4 Clock Pair Outputs Support Stacked DDR3 RDIMMs
CKE Powerdown Mode for Optimized System Power Consumption
1.5V/1.35V Phase Lock Loop Clock Driver for Buffering One Differential Clock Pair (CK and CK) and Distributing to Four Differential Outputs
1.5V/1.35V CMOS Inputs
Checks Parity on Command and Address (CS-Gated) Data Inputs
Configurable Driver Strength
Uses Internal Feedback Loop
APPLICATIONS
- DDR3 Registered DIMMs up to DDR3-1600
- DDR3L Registered DIMMs up to DDR3L-1333
- Single-, Dual- and Quad-Rank RDIMM

下面可能是您感兴趣的TI德州仪器公司DDR3寄存器元器件

TI公司产品现货专家，订购TI公司产品不限最低起订量，TI芯片大陆现货即时发货，香港库存3-5天发货，海外库存7-10天发货

寻找全球TI代理商现货货源 - TI公司（德州仪器）电子元件在线订购