TLK2211 - 0.6 至 1.3Gbps 以太网收发器

TLK2211是TI德州仪器公司的一款1G-40G以太网/光纤通道收发器产品，TLK2211是0.6 至 1.3Gbps 以太网收发器，本站介绍了TLK2211的封装应用图解、特点和优点、功能等，并给出了与TLK2211相关的TI元器件型号供参考。

TLK2211 - 0.6 至 1.3Gbps 以太网收发器 - 1G-40G以太网/光纤通道收发器 - 串行器、解串器 - 德州仪器

产品描述

The TLK2211 gigabit ethernet transceiver provide for ultrahigh-speed full-duplex point-to-point data transmissions. These devices are based on the timing requirements of the 10-bit interface specification by the IEEE 802.3 Gigabit Ethernet specification. The TLK2211 supports data rates from 1.0 Gbps through 1.3 Gbps.

The primary application of this device is to provide building blocks for point-to-point baseband data transmission over controlled impedance media of 50 Ω or 75 Ω. The transmission media can be printed-circuit board traces, copper cables or fiber-optical media. The ultimate rate and distance of data transfer is dependent upon the attenuation characteristics of the media and the noise coupling to the environment.

The TLK2211 performs the data serialization, deserialization, and clock extraction functions for a physical layer interface device. The transceiver operates at 1.25 Gbps (typical), providing up to 1 Gbps of data bandwidth over a copper or optical media interface.

The TLK2211 supports a standard 10-bit interface (TBI) . In the TBI mode the serializer/deserializer (SERDES) accepts 10-bit wide 8b/10b parallel encoded data bytes. The parallel data bytes are serialized and transmitted differentially at PECL compatible voltage levels. The SERDES extracts clock information from the input serial stream and deserializes the data, outputting a parallel 10-bit data byte.

The TLK2211 provides a comprehensive series of built-in tests for self-test purposes including loopback and pseudo random binary sequence (PRBS) generation and verification. An IEEE 1149.1 JTAG port is also supported.

The TLK2211 is housed in a high performance, thermally enhanced, 64-pin VQFP PowerPAD package. Use of the PowerPAD package does not require any special considerations except to note that the PowerPAD, which is an exposed die pad on the bottom of the device, is a metallic thermal and electrical conductor. It is recommended that the TLK2211 PowerPADs be soldered to the thermal land on the board.

The TLK2211 is characterized for operation from –40°C to 85°C.

The TLK2211 use a 3.3-V supply. The I/O section is 3.3-V compatible. With the 3.3-V supply the chipset is very power-efficient, dissipating less than 600 mW typical power when operating at 1.25 Gbps.

The TLK2211 is designed to be hot plug capable. A power-on reset causes RBC0, RBC1, the parallel output signal terminals, TXP, and TXN to be held in high-impedance state.

产品特性

600 mbps to 1.3 Gigabits Per Second (Gbps) Serializer/Deserializer
Low Power Consumption <450 mW Typical at 1.25 Gbps
LVPECL Compatible Differential I/O on High Speed Interface
Single Monolithic PLL Design
Support For 10 Bit Interface
Receiver Differential Input Thresholds 200 mV Minimum
Industrial Temperature Range From –40°C to 85°C
IEEE 802.3 Gigabit Ethernet Compliant
Advanced 0.25 µm CMOS Technology
No External Filter Capacitors Required
Comprehensive Suite of Built-In Testability
IEEE 1149.1 JTAG Support
3.3 V Supply Voltage for Lowest Power Operation
3.3 V Tolerant on LVTTL Inputs
Hot Plug Protection
64 Pin VQFP With Thermally Enhanced Package (PowerPAD)

下面可能是您感兴趣的TI德州仪器公司1G-40G以太网/光纤通道收发器元器件

TI公司产品现货专家，订购TI公司产品不限最低起订量，TI芯片大陆现货即时发货，香港库存3-5天发货，海外库存7-10天发货

寻找全球TI代理商现货货源 - TI公司（德州仪器）电子元件在线订购