The TM4C123FE6PM microcontroller is targeted for industrial applications, including remote monitoring, electronic point-of-sale machines, test and measurement equipment, network appliances and switches, factory automation, HVAC and building control, gaming equipment, motion control, transportation, and fire and security.

• 32-bit ARM? Cortex?-M4 80-MHz processor core with System Timer (SysTick), integrated Nested Vectored Interrupt Controller (NVIC), Wake-Up Interrupt Controller (WIC) with clock gating, Memory Protection Unit (MPU), IEEE754-compliant single-precision Floating-Point Unit (FPU), Embedded Trace Macro and Trace Port, System Control Block (SCB) and Thumb-2 instruction set

• On-chip memory, featuring 128 KB single-cycle Flash up to 40 MHz (a prefetch buffer improves performance above 40 MHz), 32 KB single-cycle SRAM; internal ROM loaded with TivaWare? for C Series software; 2KB EEPROM

• Two Controller Area Network (CAN) modules, using CAN protocol version 2.0 part A/B and with bit rates up to 1 Mbps

• Universal Serial Bus (USB) controller with USB 2.0 full-speed (12 Mbps) and low-speed (1.5 Mbps) operation, 32 endpoints, and USB OTG/Host/Device mode

• Advanced serial integration, featuring: eight UARTs with IrDA, 9-bit, and ISO 7816 support (one UART with modem status and modem flow control); four Synchronous Serial Interface (SSI) modules, supporting operation for Freescale SPI, MICROWIRE, or Texas Instruments synchronous serial interfaces; six Inter-Integrated Circuit (I2C) modules, providing Standard (100 Kbps) and Fast (400 Kbps) transmission and support for sending and receiving data as either a master or a slave

• ARM PrimeCell? 32-channel configurable μDMA controller, providing a way to offload data transfer tasks from the Cortex?-M4 processor, allowing for more efficient use of the processor and the available bus bandwidth

• Analog support, featuring: two 12-bit Analog-to-Digital Converters (ADC) with 12 analog input channels and a sample rate of one million samples/second; two analog comparators; 16 digital comparators; on-chip voltage regulator

• Advanced motion control, featuring: eight Pulse Width Modulation (PWM) generator blocks, each with one 16-bit counter, two PWM comparators, a PWM signal generator, a dead-band generator, and an interrupt/ADC-trigger selector; six PWM fault inputs to promote low-latency shutdown; two Quadrature Encoder Interface (QEI) modules, with position integrator to track encoder position and velocity capture using built-in timer

• Two ARM FiRM-compliant watchdog timers; six 32-bit general-purpose timers (up to twelve 16-bit); six wide 64-bit general-purpose timers (up to twelve 32-bit); 12 16/32-bit and 12 32/64-bit Capture Compare PWM (CCP) pins

• Up to 49 GPIOs (depending on configuration), with programmable control for GPIO interrupts and pad configuration, and highly flexible pin muxing

• Multiple clock sources for microcontroller system clock: Precision Oscillator (PIOSC), Main Oscillator (MOSC), and Internal 30-kHz Oscillator

• Full-featured debug solution with debug access via JTAG and Serial Wire interfaces, and IEEE 1149.1-1990 compliant Test Access Port (TAP) controller

• Industrial-range (-40°C to 85°C) RoHS-compliant 64-pin LQFP

  下面可能是您感兴趣的TI公司控制+自动化元器件
• ADS931 - 8 位 30MSPS ADC，具有单端/差动输入和外部基准 以及低功耗、电源关闭功能
• MSP430FR5732 - MSP430FR573x MSP430FR572x 混合信号微控制器
• ISO7221A-Q1 - 汽车类双通道 1/1 1Mbps 数字隔离器
• SN65HVD32 - 3.3V 全双工 RS 485 驱动器和接收器
• UCC27425 - 具有使能端的双路 4A MOSFET 驱动器
• SN74F138 - 3 线路到 8 线路解码器/多路解复用器
• CD54HCT30 - 高速 CMOS 逻辑 8 输入与非门
• SN75ALS171 - 三路差动总线收发器
• AM26LV32E - 具有 +/-15kV IEC ESD 的低电压高速四路差动线路接收器
• SN74CBTS16211 - 具有肖特基二极管钳位功能的 24 位 FET 总线开关