The TPS563900 device is a monolithic dual-synchronous buck converter with a wide 4.5-V to 18-V operating input-voltage range that can operate in 5-, 9-, 12-, or 15-V bus voltages and battery chemistries. Constant-frequency peak-current mode control simplifies the loop compensation and provides fast transient response.

External feedback resistors can be used to set the initial start-up voltage for each buck converter in the TPS563900 device. The feedback voltage reference for this start-up option is 0.6 V. When the voltage-identification (VID) DAC is updated through the I2C, the buck converter switches the feedback resistors from external to internal feedback resistors. The output voltage in each buck is programmable from 0.68 V to 1.95 V with 10-mV steps by I2C-controlled 7-bit VID.

Each buck converter in the TPS563900 device can also be I2C controlled for enabling and disabling the output voltage, reading the output voltage, setting the pulse skipping mode, and reading the power good status and the warning of die temperature.

The TPS563900 device features a dedicated enable pin when the I2C interface is not used. An independent soft-start pin provides flexibility in power-up programmability. Cycle-by-cycle overcurrent protection and hiccup-mode operation limit MOSFET power dissipation in short circuit or over-loading fault conditions. Low-side reverse overcurrent protection also prevents excessive sinking current from damaging the converter.

The TPS563900 device also features a light-load pulse-skipping mode (PSM) that can be controlled by the I2C or MODE pin configuration. The PSM mode allows a power loss reduction on the input power supplied to the system to achieve high efficiency at light loading.

The TPS563900 device is available in a 32-lead thermally-enhanced HTSSOP (DAP) package.

• 4.5-V to 18-V Wide Input Voltage Range
• I2C Controlled 7-Bits VID Programmable Output Voltage from 0.68 V to 1.95 V with 10-mV Steps for Each Buck; Output Voltage can also be Set by Resistor Divider
• Programmable Slew-Rate Control for Output-Voltage Transition
• Up to 3.5-A Maximum Continuous Output Current in Buck 1 and Buck 2
• Buck 1 and Buck 2 can be Paralleled to Deliver up to 7-A Current
• I2C Compatible Interface With Standard Mode (100 kHz) and Fast Mode (400 kHz)
• I2C Read Back Power Good Status and Die Temperature Warning
• Pulse-Skipping Mode to Achieve High Efficiency in Light Loads
• Adjustable Switching Frequency 200 kHz to 1.6 MHz Set by External Resistor
• Dedicated Enable and Soft-Start for Each Buck
• Peak Current-Mode Control With Simple Compensation Circuit
• Cycle-by-Cycle Overcurrent Protection
• 180° Out-of-Phase Operation to Reduce Input Filter and Power Supply Conduced Noise
• Overtemperature Protection
• Available in 32-Pin Thermally Enhanced HTSSOP (DAP) Package

• F28M35M52C - Concerto 微处理器
• MSP430F47196 - 16 位超低功耗微控制器，具有 120KB 闪存、4KB RAM、6 个 Σ-Δ ADC 和 LCD 驱动器
• ADS8674 - 14 位、500 kSPS、4 通道和 8 通道、单电源 SAR 模数转换器 (ADC)
• TLC3574 - 串行输出低功耗具有内置转换时钟的 & 8x FIFO，4 通道
• PCA9535 - 具有中断输出和配置寄存器的远程 16 位 I2C 和 SMBus 低功耗 I/O 扩展器
• BQ25896 - bq25896/7 具有 NVDC 电源路径管理的 I2C 控制 5A 单节 USB/适配器充电器
• ADS8664 - 12 位、4 通道、软件可编程输入范围、250kSPS、ADC
• TPS63011 - 具有 2A 开关的高效率、单电感器、降压升压转换器
• ADS58C20 - 双通道 IF BTS 接收器，具有用于多模式 3G+LTE+GSM 的信号处理
• BQ24071 - Single-Chip Charge and System Power-Path Managment IC