TPS60212 - 具有超低操作电流的稳压 3.3V 50mA 低纹波充电泵

TPS60212是TI德州仪器公司的一款电荷泵（无感应器）产品，TPS60212是具有超低操作电流的稳压 3.3V 50mA 低纹波充电泵，本站介绍了TPS60212的封装应用图解、特点和优点、功能等，并给出了与TPS60212相关的TI元器件型号供参考。

TPS60212 - 具有超低操作电流的稳压 3.3V 50mA 低纹波充电泵 - 电荷泵（无感应器） - DC/DC开关稳压器 - 德州仪器

产品描述

The TPS6021x step-up, regulated charge pumps generate a 3.3-V ±4% output voltage from a 1.8-V to 3.6-V input voltage. These devices are typically powered by two alkaline, NiCd, or NiMH battery cells or by one primary lithium MnO2 (or similar) coin cell and operate down to a minimum supply voltage of 1.6 V. Continuous output current is a minimum of 100 mA for the TPS60210 and TPS60211, and 50 mA for the TPS60212 and TPS60213, all from a 2-V input.

Three operating modes can be programmed using the SNOOZE\ pin. When SNOOZE\ is low, the device is put into snooze mode. In snooze mode, the device operates with a typical quiescent current of 2 uA while the output voltage is maintained at 3.3 V ±6%. This is lower than the self-discharge current of most batteries. Load current in snooze mode is limited to 2 mA. When SNOOZE\ is high, the device is put into normal operating mode. During normal operating mode, the device operates in the newly developed linskip mode where it switches seamlessly from the power saving pulse-skip mode at light loads to the low-noise constant-frequency linear-regulation mode once the output current exceeds the linskip current threshold of about 7 mA. In this mode, the device operates from the internal oscillator. The device is synchronized to an external clock signal if SNOOZE\ is clocked; thus switching harmonics can be controlled and minimized.

Only four external capacitors are needed to build a complete low-ripple dc/dc converter. The push-pull operating mode of two single-ended charge pumps assures the low output voltage ripple as charge is continuously transferred to the output. All the devices can start with full load current. The devices include a low-battery detector that issues a warning if the battery voltage drops below a user-defined threshold voltage or a power-good detector that goes active when the output voltage reaches about 90% of its nominal value. This dc/dc converter requires no inductors; therefore, EMI of the system is reduced to a minimum, making it easier to use in designs. It is available in the small 10-pin MSOP package (DGS).

产品特性

Regulated 3.3-V Output Voltage From a 1.8-V to 3.6-V Input Voltage Range
UltraLow Operating Current in Snooze Mode, Typical 2 uA With up to 2-mA Output Current
Less Than 5-mV(PP) Output Voltage Ripple Achieved With Push-Pull Topology
Integrated Low-Battery and Power-Good Detector
Switching Frequency Can Be Synchronized to External Clock Signal
Extends Battery Usage With up to 90% Efficiency and 35-uA Quiescent Current
Easy-To-Design, Low Cost, Low EMI Power Supply Since No Inductors Are Used
Compact Converter Solution in UltraSmall 10-Pin MSOP With Only Four External Capacitors Required
Evaluation Module Available (TPS60210EVM-167)
Applications
- Replaces DC/DC Converters With Inductors in Battery-Powered Applications Like:
  - Two Battery Cells to 3.3-V Conversion
  - MSP430 Ultralow-Power Microcontroller and Other Battery Powered Microprocessor Systems
  - Glucose Meters and Other Medical Instruments
  - MP3 Portable Audio Players
  - Backup-Battery Boost Converters
  - Cordless Phones, PDAs

下面可能是您感兴趣的TI德州仪器公司电荷泵（无感应器）元器件

TI公司产品现货专家，订购TI公司产品不限最低起订量，TI芯片大陆现货即时发货，香港库存3-5天发货，海外库存7-10天发货

寻找全球TI代理商现货货源 - TI公司（德州仪器）电子元件在线订购