BQ24158 - 与 USB 完全兼容的完全集成开关模式单节锂离子充电器，VOVP=6.5v

BQ24158是TI德州仪器公司的一款电池充电器IC产品，BQ24158是与 USB 完全兼容的完全集成开关模式单节锂离子充电器，VOVP=6.5v，本站介绍了BQ24158的封装应用图解、特点和优点、功能等，并给出了与BQ24158相关的TI元器件型号供参考。

BQ24158 - 与 USB 完全兼容的完全集成开关模式单节锂离子充电器，VOVP=6.5v - 电池充电器IC - 电池管理产品 - 德州仪器

产品描述

The bq24153A/6A/8/9 is a compact, flexible, high-efficiency, USB-friendly switch-mode charge management device for single-cell Li-ion and Li-polymer batteries used in a wide range of portable applications. The charge parameters can be programmed through an I2C interface. The IC integrates a synchronous PWM controller, power MOSFETs, input current sensing, high-accuracy current and voltage regulation, and charge termination, into a small WCSP package.

The IC charges the battery in three phases: conditioning, constant current and constant voltage. The input current is automatically limited to the value set by the host. Charge is terminated based on battery voltage and user-selectable minimum current level. A safety timer with reset control provides a safety backup for I2C interface. During normal operation, The IC automatically restarts the charge cycle if the battery voltage falls below an internal threshold and automatically enters sleep mode or high impedance mode when the input supply is removed. The charge status can be reported to the host using the I2C interface. During the charging process, the IC monitors its junction temperature (TJ) and reduces the charge current once TJ increases to about 125°C. To support USB OTG device, bq24153A/8 can provide VBUS (5.05V) by boosting the battery voltage. The IC is available in 20-pin WCSP package.

产品特性

Charge Faster than Linear Chargers
High-Accuracy Voltage and Current Regulation
- Input Current Regulation Accuracy: ±5% (100 mA and 500 mA)
- Charge Voltage Regulation Accuracy: ±0.5% (25°C), ±1% (0°C to 125°C)
- Charge Current Regulation Accuracy: ±5%
Input Voltage Based Dynamic Power Management (VIN DPM)
Bad Adaptor Detection and Rejection
Safety Limit Register for Maximum Charge Voltage and Current Limiting
High-Efficiency Mini-USB/AC Battery Charger for Single-Cell Li-Ion and Li-Polymer Battery Packs
20-V Absolute Maximum Input Voltage Rating
9-V Maximum Operating Input Voltage-bq24156A/9
6-V Maximum Operating Input Voltage-bq24153A/8
Built-In Input Current Sensing and Limiting
Integrated Power FETs for Up To 1.5-A Charge Rate-bq24156A/9, 1.25A-bq24153A/8
Programmable Charge Parameters through I2C Compatible Interface (up to 3.4 Mbps):
- Input Current Limit
- VIN DPM Threshold
- Fast-Charge/Termination Current
- Charge Regulation Voltage (3.5 V to 4.44 V)
- Low Charge Current Mode Enable/Disable
- Safety Timer with Reset Control
- Termination Enable/Disable
Synchronous Fixed-Frequency PWM Controller Operating at 3 MHz With 0% to 99.5% Duty Cycle
Automatic High Impedance Mode for Low Power Consumption
Robust Protection
- Reverse Leakage Protection Prevents Battery Drainage
- Thermal Regulation and Protection
- Input/Output Overvoltage Protection
Status Output for Charging and Faults
USB Friendly Boot-Up Sequence
Automatic Charging
Power Up System without Battery bq24158/9
Boost Mode Operation for USB OTG: (bq24153A/8 only)
- Input Voltage Range (from Battery): 2.5 V to 4.5 V
- Output for VBUS: 5.05 V/ 200 mA
2.1 mm × 2 mm 20-Pin WCSP Package
APPLICATIONS
- Mobile and Smart Phones
- MP3 Players
- Handheld Devices

下面可能是您感兴趣的TI德州仪器公司电池充电器IC元器件

TI公司产品现货专家，订购TI公司产品不限最低起订量，TI芯片大陆现货即时发货，香港库存3-5天发货，海外库存7-10天发货

寻找全球TI代理商现货货源 - TI公司（德州仪器）电子元件在线订购