MAX3221E - 3V 至 5.5V 单通道 RS-232 线路驱动器/接收器

MAX3221E是TI德州仪器公司的一款无产品，MAX3221E是3V 至 5.5V 单通道 RS-232 线路驱动器/接收器，本站介绍了MAX3221E的封装应用图解、特点和优点、功能等，并给出了与MAX3221E相关的TI元器件型号供参考。

MAX3221E - 3V 至 5.5V 单通道 RS-232 线路驱动器/接收器 - 无 - RS-232收发器 - 德州仪器

产品描述

产品特性

ESD Protection for RS-232 Pins
- ±15-kV Human-Body Model (HBM)
- ±8 kV (IEC 61000-4-2, Contact Discharge)
- ±15 kV (IEC 61000-4-2, Air-Gap Discharge)
Meets or Exceeds the Requirements of TIA/EIA-232-F and ITU v.28 Standards
Operates With 3-V to 5.5-V VCC Supply
Operates up to 250 kbit/s
One Driver and One Receiver
Low Standby Current . . . 1 µA Typ
External Capacitors . . . 4 × 0.1 µF
Accepts 5-V Logic Input With 3.3-V Supply
Alternative High-Speed Pin-Compatible Device (1 Mbit/s)
- SN75C3221E and SN65C3221E
Auto-Powerdown Feature Automatically Disables Drivers for Power Savings
APPLICATIONS
- Battery-Powered, Hand-Held, and Portable Equipment
- PDAs and Palmtop PCs
- Notebooks, Subnotebooks, and Laptops
- Digital Cameras
- Mobile Phones and Wireless Devices

DESCRIPTION/ORDERING INFORMATION

The MAX3221E is a single driver, single receiver RS-232 solution operating from a single VCC supply. The RS-232 pins provide IEC G1000-4-2 ESD protection. The device meets the requirements of TIA/EIA-232-F and provides the electrical interface between an asynchronous communication controller and the serial-port connector. The charge pump and four small external capacitors allow operation from a single 3-V to 5.5-V supply. These devices operate at data signaling rates up to 250 kbit/s and a maximum of 30-V/µs driver output slew rate.

Flexible control options for power management are available when the serial port is inactive. The auto-powerdown feature functions when FORCEON is low and FORCEOFF is high. During this mode of operation, if the device does not sense a valid RS-232 signal on the receiver input, the driver output is disabled. If FORCEOFF is set low and EN is high, both the driver and receiver are shut off, and the supply current is reduced to 1 µA. Disconnecting the serial port or turning off the peripheral drivers causes the auto-powerdown condition to occur. Auto-powerdown can be disabled when FORCEON and FORCEOFF are high. With auto-powerdown enabled, the device is activated automatically when a valid signal is applied to the receiver input. The INVALID output notifies the user if an RS-232 signal is present at the receiver input. INVALID is high (valid data) if the receiver input voltage is greater than 2.7 V or less than -2.7 V, or has been between -0.3 V and 0.3 V for less than 30 µs. INVALID is low (invalid data) if the receiver input voltage is between -0.3 V and 0.3 V for more than 30 µs.

下面可能是您感兴趣的TI德州仪器公司无元器件

TI公司产品现货专家，订购TI公司产品不限最低起订量，TI芯片大陆现货即时发货，香港库存3-5天发货，海外库存7-10天发货

寻找全球TI代理商现货货源 - TI公司（德州仪器）电子元件在线订购