MSP430FR2633 - MSP430FR263x 和 MSP430FR253x 混合信号微控制器

MSP430FR2633是TI德州仪器公司的一款超低功耗产品，MSP430FR2633是MSP430FR263x 和 MSP430FR253x 混合信号微控制器，本站介绍了MSP430FR2633的封装应用图解、特点和优点、功能等，并给出了与MSP430FR2633相关的TI元器件型号供参考。

MSP430FR2633 - MSP430FR263x 和 MSP430FR253x 混合信号微控制器 - 超低功耗 - 低功耗MCU - 德州仪器

1 Device Overview

1.1 Features

Embedded Microcontroller
- 16-Bit RISC Architecture
- Clock Supports Frequencies up to 16 MHz
- Wide Supply Voltage Range From 1.8V to 3.6V (1)
Optimized Ultra-Low-Power Modes
- Active Mode: 126 µA/MHz (Typical)
- Standby
  - 1.7 µA/Button Average (Typical) (16 Self-Capacitance Buttons, 8-Hz Scanning)
  - 1.7 µA/Button Average (Typical) (64 Mutual-Capacitance Buttons, 8-Hz Scanning)
- LPM3.5 Real-Time Clock (RTC) Counter With 32768-Hz Crystal: 770 nA (Typical)
- Shutdown (LPM4.5): 15 nA (Typical)
Low-Power Ferroelectric RAM (FRAM)
- Up to 15.5KB of Nonvolatile Memory
- Built-In Error Correction Code (ECC)
- Configurable Write Protection
- Unified Memory of Program, Constants, and Storage
- 1015 Write Cycle Endurance
- Radiation Resistant and Nonmagnetic
- High FRAM-to-SRAM Ratio, up to 4:1
Intelligent Digital Peripherals
- Four 16-Bit Timers
  - Two Timers With Three Capture/Compare Registers Each (Timer_A3)
  - Two Timers With Two Capture/Compare Registers Each (Timer_A2)
- One 16-Bit Timer Associated With CapTIvate™ Technology
- One 16-Bit Counter-Only RTC
- 16-Bit Cyclic Redundancy Check (CRC)
Enhanced Serial Communications
- Two Enhanced Universal Serial Communication Interfaces (eUSCI_A) Support UART, IrDA, and SPI
- One eUSCI (eUSCI_B) Supports SPI and I2C
High-Performance Analog
- 8-Channel 10-Bit Analog-to-Digital Converter (ADC)
  - Internal 1.5-V Reference
  - Sample-and-Hold 200 ksps
- CapTIvate Technology – Capacitive Touch
  - Performance
    - Fast Electrode Scanning With Four Simultaneous Scans
    - Support for High-Resolution Sliders With >1024 Points
    - 30-cm Proximity Sensing
  - Reliability
    - Increased Immunity to Power Line, RF, and Other Environmental Noise
    - Built-in Spread Spectrum, Automatic Tuning, Noise Filtering, and Debouncing Algorithms
    - Enables Reliable Touch Solutions With 10-V RMS Common-Mode Noise, 4-kV Electrical Fast Transients, and 15-kV Electrostatic Discharge, Allowing for IEC?61000-4-6, IEC-61000-4-4, and IEC?61000-4-2 Compliance
    - Reduced RF Emissions to Simplify Electrical Designs
    - Support for Metal Touch and Water Rejection Designs
  - Flexibility
    - Up to 16 Self-Capacitance and 64 Mutual-Capacitance Electrodes
    - Mix and Match Self- and Mutual-Capacitive Electrodes in the Same Design
    - Supports Multitouch Functionality
    - Wide Range of Capacitance Detection, Wide Electrode Range of 0 to 300 pF
  - Low Power
    - <0.9 µA/Button in Wake-on-Touch Mode, Where Capacitive Measurement and Touch Detection is Done by Hardware State Machine While CPU is Asleep
    - Wake-on-Touch State Machine Allows Electrode Scanning While CPU is Asleep
    - Hardware Acceleration for Environmental Compensation, Filtering, and Threshold Detection
  - Ease of Use
    - CapTIvate Design Center, PC GUI Lets Engineers Design and Tune Capacitive Buttons in Real Time Without Having to Write Code
    - CapTIvate Software Library in ROM Provides Ample FRAM for Customer Application
Clock System (CS)
- On-Chip 32-kHz RC Oscillator (REFO)
- On-Chip 16-MHz Digitally Controlled Oscillator (DCO) With Frequency-Locked Loop (FLL)
  - ±1% Accuracy With On-Chip Reference at Room Temperature
- On-Chip Very Low-Frequency 10-kHz Oscillator (VLO)
- On-Chip High-Frequency Modulation Oscillator (MODOSC)
- External 32-kHz Crystal Oscillator (LFXT)
- Programmable MCLK Prescalar of 1 to 128
- SMCLK Derived from MCLK With Programmable Prescalar of 1, 2, 4, or 8
General Input/Output and Pin Functionality
- Total of 19 I/Os on TSSOP-32 Package
- 16 Interrupt Pins (P1 and P2) Can Wake MCU From Low-Power Modes
Development Tools and Software
- Ease-of-Use Ecosystem
  - CapTIvate Design Center – Code Generation, Customizable GUI, Real-Time Tuning
- Free Professional Development Environments
12-KB ROM Library Includes CapTIvate Touch Libraries and Driver Libraries
Family Members (Also See Section 3)
- MSP430FR2633: 15KB of Program FRAM + 512B of Information FRAM + 4KB of RAM up to 16 Self-Capacitive and 64 Mutual-Capacitive Sensors
- MSP430FR2533: 15KB of Program FRAM + 512B of Information FRAM + 2KB of RAM up to 16 Self-Capacitive or 16 Mutual-Capacitive Sensors
- MSP430FR2632: 8KB of Program FRAM + 512B of Information FRAM + 2KB of RAM up to 8 Self-Capacitive or 16 Mutual-Capacitive Sensors
- MSP430FR2532: 8KB of Program FRAM + 512B of Information FRAM + 1KB of RAM up to 8 Self-Capacitive or 8 Mutual-Capacitive Sensors
Package Options
- 32-Pin: VQFN (RHB)
- 32-Pin: TSSOP (DA)
- 24-Pin: VQFN (RGE)
For Complete Module Descriptions, See the MSP430FR4xx and MSP430FR2xx Family User's Guide (SLAU445)

(1) Minimum supply voltage is restricted by SVS levels (see VSVSH- and VSVSH+ in Table 5-2)

1.2 Applications

Thermostats
Electronic Access Control
Lighting Control
Electronic Door Locks
White Goods
Small Appliances
Personal Electronics

1.3 Description

The MSP430FR263x and MSP430FR253x are FRAM-based ultra-low-power MSP microcontrollers that feature CapTIvate touch technology for buttons, sliders, wheels (BSW), and proximity applications. CapTIvate technology provides the highest resolution capacitive-touch solution in the market with high reliability and noise immunity at the lowest power. CapTIvate technology supports concurrent self-capacitance and mutual-capacitance electrodes on the same design for maximum flexibility. Using the CapTIvate Design Center, engineers can quickly develop BSW applications with an easy-to-use GUI.

The TI MSP family of low-power microcontrollers consists of several devices that feature different sets of peripherals targeted for various applications. The architecture, combined with extensive low-power modes, is optimized to achieve extended battery life in portable measurement applications. The MCU features a powerful 16-bit RISC CPU, 16-bit registers, and constant generators that contribute to maximum code efficiency. The digitally controlled oscillator (DCO) allows the MCU to wake up from low-power modes to active mode typically in less than 10 µs.

产品器件信息

PART NUMBER	PACKAGE	BODY SIZE(2)
MSP430FR2633IRHB	VQFN (32)	5 mm × 5 mm
MSP430FR2533IRHB	VQFN (32)	5 mm × 5 mm
MSP430FR2633IDA	TSSOP (32)	11 mm × 6.2 mm
MSP430FR2533IDA	TSSOP (32)	11 mm × 6.2 mm
MSP430FR2632IRGE	VQFN (24)	4 mm × 4 mm
MSP430FR2532IRGE	VQFN (24)	4 mm × 4 mm

下面可能是您感兴趣的TI德州仪器公司超低功耗元器件

TI公司产品现货专家，订购TI公司产品不限最低起订量，TI芯片大陆现货即时发货，香港库存3-5天发货，海外库存7-10天发货

寻找全球TI代理商现货货源 - TI公司（德州仪器）电子元件在线订购