A Dynamic Output Control (DOC) circuit is implemented, which, during the transition, initially lowers the output impedance to effectively drive the load and, subsequently, raises the impedance to reduce noise. Figure 1 shows typical VOL vs IOL and VOH vs IOH curves to illustrate the output impedance and drive capability of the circuit. At the beginning of the signal transition, the DOC circuit provides a maximum dynamic drive that is equivalent to a high-drive standard-output device. For more information, refer to the TI application reports, AVC Logic Family Technology and Applications, literature number SCEA006, and Dynamic Output Control (DOC™ ) Circuitry Technology and Applications, literature number SCEA009.

This 16-bit edge-triggered D-type flip-flop is operational at 1.2-V to 3.6-V VCC, but is designed specifically for 1.65-V to 3.6-V VCC operation.

The SN74AVC16374 is particularly suitable for implementing buffer registers, I/O ports, bidirectional bus drivers, and working registers. It can be used as two 8-bit flip-flops or one 16-bit flip-flop. On the positive transition of the clock (CLK) input, the Q outputs of the flip-flop take on the logic levels at the data (D) inputs. OE\ can be used to place the eight outputs in either a normal logic state (high or low logic levels) or the high-impedance state. In the high-impedance state, the outputs neither load nor drive the bus lines significantly. The high-impedance state and the increased drive provide the capability to drive bus lines without need for interface or pullup components.

OE\ does not affect internal operations of the flip-flop. Old data can be retained or new data can be entered while the outputs are in the high-impedance state.

To ensure the high-impedance state during power up or power down, OE\ should be tied to VCC through a pullup resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver.

This device is fully specified for partial-power-down applications using Ioff. The Ioff circuitry disables the outputs, preventing damaging current backflow through the device when it is powered down.

The SN74AVC16374 is characterized for operation from -40°C to 85°C.

• Member of the Texas Instruments Widebus™ Family
• EPIC™ (Enhanced-Performance Implanted CMOS) Submicron Process
• DOC™ (Dynamic Output Control) Circuit Dynamically Changes Output Impedance, Resulting in Noise Reduction Without Speed Degradation
• Dynamic Drive Capability Is Equivalent to Standard Outputs With IOH and IOL of ±24 mA at 2.5-V VCC
• Overvoltage-Tolerant Inputs/Outputs Allow Mixed-Voltage-Mode Data Communications
• Ioff Supports Partial-Power-Down Mode Operation
• ESD Protection Exceeds JESD 22
  • 2000-V Human-Body Model (A114-A)
  • 200-V Machine Model (A115-A)
• Latch-Up Performance Exceeds 100 mA Per JESD 78, Class II
• Package Options Include Plastic Thin Shrink Small-Outline (DGG) and Thin Very Small-Outline (DGV) Packages

DOC, EPIC, and Widebus are trademarks of Texas Instruments.

• TNETE2201B - 1.25 千兆以太网收发器
• TPS59610 - 用于 IMVP6+ CPU 和图形 Vcore 嵌入式计算的单相 D-CAP+? 同步降压控制器
• TPS562209 - 具有高级 Eco-mode? 的 4.5V 至 18V 输入，4A 同步降压转换器
• CD4536B - CMOS 可编程定时器
• TPD1E6B06 - 采用 0201 封装的单通道 ESD PROSingle 通道 ESD，具有采用 0201 封装的 6pF CapaTECTION 器件
• TPS43330A-Q1 - 低 IQ、单路升压、固定电压、双路同步降压控制器
• TS5A22364-Q1 - 具有负轨功能的汽车类 0.65Ω 双路 SPDT 模拟开关
• TPIC6259 - 8 位可寻址锁存器
• LM74A - 具有 Microwire 和 SPI 接口的 ±3°C 芯片式温度传感器
• TLC59108F - 8 位快速模式+ (FM+) 12C 总线 LED 驱动器