The 'GTL16612 devices are 18-bit UBT™ transceivers that provide LVTTL-to-GTL/GTL+ and GTL/GTL+-to-LVTTL signal-level translation. They combine D-type flip-flops and D-type latches to allow for transparent, latched, clocked, and clock-enabled modes of data transfer identical to the '16601 function. The devices provide an interface between cards operating at LVTTL logic levels and a backplane operating at GTL/GTL+ signal levels. Higher-speed operation is a direct result of the reduced output swing (<1 V), reduced input threshold levels, and OEC™ circuitry.

The user has the flexibility of using these devices at either GTL (VTT = 1.2 V and VREF = 0.8 V) or the preferred higher noise margin GTL+ (VTT = 1.5 V and VREF = 1 V) signal levels. GTL+ is the Texas Instruments derivative of the Gunning Transceiver Logic (GTL) JEDEC standard JESD 8-3. The B port normally operates at GTL or GTL+ signal levels, while the A-port and control inputs are compatible with LVTTL logic levels and are 5-V tolerant. VREF is the reference input voltage for the B port.

VCC (5 V) supplies the internal and GTL circuitry while VCC (3.3 V) supplies the LVTTL output buffers.

Data flow in each direction is controlled by output-enable (OEAB\ and OEBA\), latch-enable(LEAB and LEBA), and clock (CLKAB and CLKBA) inputs. The clock can be controlled by the clock-enable (CEAB\ and CEBA\) inputs. For A-to-B data flow, the devices operate in the transparent mode when LEAB is high. When LEAB is low, the A data is latched if CEAB\ is low and CLKAB is held at a high or low logic level. If LEAB is low, the A data is stored in the latch/flip-flop on the low-to-high transition of CLKAB if CEAB\ also is low. When OEAB\ is low, the outputs are active. When OEAB\ is high, the outputs are in the high-impedance state. Data flow for B to A is similar to that for A to B, but uses OEBA\, LEBA, CLKBA, and CEBA\.

These devices are fully specified for partial-power-down applications using Ioff. The Ioff circuitry disables the outputs, preventing damaging current backflow through the device when it is powered down.

Active bus-hold circuitry holds unused or undriven LVTTL inputs at a valid logic state. Use of pullup or pulldown resistors with the bus-hold circuitry is not recommended.

• Members of Texas Instruments' Widebus™ Family
• UBT™ Transceivers Combine D-Type Latches and D-Type Flip-Flops for Operation in Transparent, Latched, Clocked, or Clock-Enabled Modes
• OEC™ Circuitry Improves Signal Integrity and Reduces Electromagnetic Interference
• Translate Between GTL/GTL+ Signal Levels and LVTTL Logic Levels
• Support Mixed-Mode (3.3 V and 5 V) Signal Operation on A-Port and Control Inputs
• Identical to \x9216601 Function
• Ioff Supports Partial-Power-Down Mode Operation
• Bus Hold on Data Inputs Eliminates the Need for External Pullup/Pulldown Resistors on A Port
• Distributed VCC and GND Pins Minimize High-Speed Switching Noise
• Latch-Up Performance Exceeds 500 mA Per JESD 17

OEC, UBT, and Widebus are trademarks of Texas Instruments.

• CSD16323Q3 - N 通道 NexFET? 功率 MOSFET
• TAS2521 - 具有嵌入式微型数字信号处理器 (miniDSP) 和单声道头戴式耳机放大器的数字输入 D 类扬声器放大器
• CD74AC151 - 8 输入多路复用器
• UCC25600 - 8 引脚高性能谐振模式控制器
• TPS62400 - 具有 1 线接口、采用 QFN 封装的双路可调节 400mA 和 600mA、2.25MHz 步降转换器
• TPS7A7100 - 单路输出、极低输入、可配置固定（0.9 至 5.0V）1A 低压降线性稳压器
• DS125MB203 - 12.5Gbps 双端口 MUX 和扇出缓冲器
• UCC2800-EP - 增强型产品低功耗 Bicmos 电流模式 Pwm
• SN74F30 - 8 输入正与非门
• CD54HC4351 - 带锁存器的高速 CMOS 逻辑 8 通道模拟多路复用器/多路解复用器