TLC5911 - 16 通道 LED 驱动器

TLC5911是TI德州仪器公司的一款标牌/线性产品，TLC5911是16 通道 LED 驱动器，本站介绍了TLC5911的封装应用图解、特点和优点、功能等，并给出了与TLC5911相关的TI元器件型号供参考。

TLC5911 - 16 通道 LED 驱动器 - 标牌/线性 - LED驱动器 - 德州仪器

产品描述

The TLC5911 is a constant current driver incorporating shift register, data latch, and constant current circuitry with a current value adjustable, PLL circuitry for gray scale control clock generation, and 1024 gray scale display using pulse width control. The output current is maximum 80 mA with 16 bits, and the current value of constant current output can be set by one external resistor. The device has two channel I/O ports. The brightness deviation between LED modules (ICs) can be adjusted by external data input from the display data port, and the brightness control for the panel can be accomplished by the brightness adjustment circuitry. Independent of these functions, the device incorporates the shift register and data latch to correct the deviation between LEDs by adjusting the output current using data from the dot correction data port. Moreover, the device incorporates WDT circuitry, which turns constant current output off when the scan signal stops during the dynamic scanning operation, and TSD circuitry, which turns constant current output off when the junction temperature exceeds the limit. Also the LED open detection (LOD) circuitry is used to make error signal output at the LED disconnection.

产品特性

Drive Capability and Output Counts
- 80 mA (Current Sink) x 16 Bits
Constant Current Output Range
- 5 to 80 mA (Current Value Setting for All Output Terminals Using External Resistor and Internal Brightness Control Register)
Constant Current Accuracy
- ±4 % (Maximum Error Between Bits)
Voltage Applied to Constant Current Output Terminals
- Minimum 0.4 V (Output Current 5 mA to 40 mA)
- Minimum 0.7 V (Output Current 40 mA to 80 mA)
1024 Gray Scale Display
- Pulse Width Control 1024 Steps
Brightness Adjustment
- All Output Current Adjustment for 64 Steps (Adjustment for Brightness Deviation Between LED Modules)
- Output Current Adjustment by Output (OUT0 to OUT15) for 128 Steps (Adjustment for Brightness Deviation Between Dots)
- Brightness Control by 16 Steps Frequency Division Gray Scale Control Clock (Brightness Adjustment for Panel)
Gray Scale Clock Generation
- Gray Scale Control Clock Generation by Internal PLL or External Input Selectable
Clock Invert/Noninvert Selectable at Cascade Operation
- Clock Invert Selectable to Reduce Changes in Duty Ratio
Protection
- Watchdog Timer (WDT) Function (Turn Output Off When Scan Signal Stopped)
- Thermal Shutdown (TSD) Function (Turn Output Off When Junction Temperature Exceeds Limit)
LOD
- LED Open Detection (Detection for LED Disconnection)
Data Input/Output
- Port A (for Data Display)
- Clock Synchronized 10 Bit Parallel Input (Schmitt-Triggered Input)
- Clock Synchronized 10 Bit Parallel Output (3-State Output)
- Port B (for Dot Correction Data)
- Clock Synchronized 7 Bit Parallel Input (Schmitt-Triggered Input)
- Clock Synchronized 7 Bit Parallel Output
Input/Output Signal Level
- CMOS Level
Power Supply Voltage
- 4.5 V to 5.5 V (Logic, Analog and Constant Current)
- 3 V to 5.5 V (Interface)
Maximum Output Voltage...15 V
Data Transfer Rate...20 MHz (Max)
Gray Scale Clock Frequency
- 16 MHz (Max) Using Internal PLL
- 8 MHz (Max) Using External Clock
Operating Free-Temperature Range -20°C to 85°C
100-Pin Package HTQFP (PD = 4.7 W, TA = 25°C)

Adjustable for these functions independently. Allows to write all the data at port A by setting.

下面可能是您感兴趣的TI德州仪器公司标牌/线性元器件

TI公司产品现货专家，订购TI公司产品不限最低起订量，TI芯片大陆现货即时发货，香港库存3-5天发货，海外库存7-10天发货

寻找全球TI代理商现货货源 - TI公司（德州仪器）电子元件在线订购