The TPS6020x step-up, regulated charge pumps generate a 3.3-V ± 4% output voltage from a 1.8-V to 3.6-V input voltage. The devices are typically powered by two Alkaline, NiCd or NiMH battery cells and operate down to a minimum supply voltage of 1.6 V. Continuous output current is a minimum of 100 mA for the TPS60200 and TPS60201 and 50 mA for the TPS60202 and TPS60203, all from a 2-V input. Only four external capacitors are needed to build a complete low-ripple dc/dc converter. The push-pull operating mode of two single-ended charge pumps assures the low output voltage ripple as current is continuously transferred to the output.

The devices operate in the newly developed LinSkip mode. In this operating mode, the device switches seamlessly from the power saving pulse-skip mode at light loads to the low-noise constant-frequency, linear-regulation mode once the output current exceeds the LinSkip threshold of about 7-mA. Even in pulse-skip mode the output ripple is maintained at a very low level because the output resistance of the charge pump is still regulated.

Three operating modes can be programmed using the EN pin. EN = low disables the device, shuts down all internal circuits and disconnects the output from the input. EN = high enables the device and programs it to run from the internal oscillator. The devices operate synchronized to an external clock signal if EN is clocked; thus switching harmonics can be controlled and minimized. The devices include a low-battery detector that issues a warning if the battery voltage drops below a user-defined threshold voltage or a power-good detector that goes active when the output voltage reaches about 90% of its nominal value.

Device options with either a low-battery or power good detector are available. This dc/dc converter requires no inductors therefore EMI of the system is reduced to a minimum. It is available in the small 10-pin MSOP package (DGS).

• Regulated 3.3-V Output Voltage With up to 100 mA Output Current From a 1.8 V to 3.6 V Input Voltage
• Less Than 5 mV(PP) Output Voltage Ripple Achieved With Push-Pull Topology
• Integrated Low-Battery and Power-Good Detector
• Switching Frequency Can Be Synchronized to External Clock Signal
• Extends Battery Usage With up to 90% Efficiency and 35 uA Quiescent Supply Current
• Reliable System Shutdown Because Output Capacitor Is Discharged When Device Is Disabled
• Easy-To-Design, Low Cost, Low EMI Power Supply Since No Inductors Are Used
• 0.05 uA Shutdown Current, Battery Is Isolated From Load in Shutdown Mode
• Compact Converter Solution in Ultra-Small 10-pin MSOP With Only Four External Capacitors Required
• Evaluation Module Available (TPS60200EVM-145)
• Applications
  • Replaces DC/DC Converters With Inductors in Battery Powered Applications Like:
    • Two Battery Cells to 3.3-V Conversion
    • MP3 Portable Audio Players
    • Battery-Powered Microprocessor Systems
    • Backup-Battery Boost Converters
    • PDA's, Organizers, Cordless Phones
    • Handheld Instrumentation
    • Glucose Meters and Other Medical Instruments

• UC3705 - 辅助高速功率驱动器
• ONET8551T - 具有 RSSI 的 11.3Gbps 限幅互阻抗放大器
• LMR62421 - 采用 SOT-23 封装的 SIMPLE SWITCHER 24V 输出电压 2.1A 升压稳压器
• SN54ACT373 - 具有三态输出的八路 D 类透明锁存器
• OPA365 - 2.2V、50MHz 低噪声单电源轨至轨运算放大器
• RM48L740 - 16/32-Bit RISC Flash Microcontroller
• ULQ2003A - 达林顿晶体管阵列
• TPS2301 - 具有独立通道电路中断功能和电源良好报告功能的 3-13V 双路热插拔 IC，工作态高电平启用
• TS12A4515 - TS12A4514, TS12A4515
• LM3203 - 具有旁通模式的微型、可调节、降压 DC-DC 转换器，用于射频功率放大器