PCA9306-Q1 - 汽车类双通道双向 I2C 总线和 SMBus 电压电平转换器

PCA9306-Q1是TI德州仪器公司的一款I2C特殊功能产品，PCA9306-Q1是汽车类双通道双向 I2C 总线和 SMBus 电压电平转换器，本站介绍了PCA9306-Q1的封装应用图解、特点和优点、功能等，并给出了与PCA9306-Q1相关的TI元器件型号供参考。

PCA9306-Q1 - 汽车类双通道双向 I2C 总线和 SMBus 电压电平转换器 - I2C特殊功能 - I2C - 德州仪器

产品描述

This dual bidirectional I2C and SMBus voltage-level translator, with an enable (EN) input, is operational from 1.2-V to 3.3-V VREF1 and 1.8-V to 5.5-V VREF2.

The PCA9306 allows bidirectional voltage translations between 1.2 V and 5 V, without the use of a direction pin. The low ON-state resistance (ron) of the switch allows connections to be made with minimal propagation delay. When EN is high, the translator switch is ON, and the SCL1 and SDA1 I/O are connected to the SCL2 and SDA2 I/O, respectively, allowing bidirectional data flow between ports. When EN is low, the translator switch is off, and a high-impedance state exists between ports.

In I2C applications, the bus capacitance limit of 400 pF restricts the number of devices and bus length. Using the PCA9306 enables the system designer to isolate two halves of a bus; thus, more I2C devices or longer trace length can be accommodated.

The PCA9306 also can be used to run two buses, one at 400-kHz operating frequency and the other at 100-kHz operating frequency. If the two buses are operating at different frequencies, the 100-kHz bus must be isolated when the 400-kHz operation of the other bus is required. If the master is running at 400 kHz, the maximum system operating frequency may be less than 400 kHz because of the delays added by the repeater.

As with the standard I2C system, pullup resistors are required to provide the logic high levels on the translator's bus. The PCA9306 has a standard open-collector configuration of the I2C bus. The size of these pullup resistors depends on the system, but each side of the repeater must have a pullup resistor. The device is designed to work with standard-mode and fast-mode I2C devices, in addition to SMBus devices. Standard-mode I2C devices only specify 3 mA in a generic I2C system where standard-mode devices and multiple masters are possible. Under certain conditions, high termination currents can be used.

When the SDA1 or SDA2 port is low, the clamp is in the ON state, and a low resistance connection exists between the SDA1 and SDA2 ports. Assuming the higher voltage is on the SDA2 port when the SDA2 port is high, the voltage on the SDA1 port is limited to the voltage set by VREF1. When the SDA1 port is high, the SDA2 port is pulled to the drain pullup supply voltage (VDPU) by the pullup resistors. This functionality allows a seamless translation between higher and lower voltages selected by the user, without the need for directional control. The SCL1/SCL2 channel also functions as the SDA1/SDA2 channel.

All channels have the same electrical characteristics, and there is minimal deviation from one output to another in voltage or propagation delay. This is a benefit over discrete transistor voltage translation solutions, since the fabrication of the switch is symmetrical. The translator provides excellent ESD protection to lower-voltage devices and at the same time protects less ESD-resistant devices.

产品特性

Qualified for Automotive Applications
AEC-Q100 Qualified With the Following Results:
- Device Temperature Grade 2: –40°C to 105°C
- Device HBM ESD Classification Level H2
- Device CDM ESD Classification Level C4B
2-Bit Bidirectional Translator for SDA and SCL Lines in Mixed-Mode I2C Applications
I2C and SMBus Compatible
Less Than 1.5-ns Maximum Propagation Delay to Accommodate Standard-Mode and Fast-Mode I2C Devices and Multiple Masters
Allows Voltage-Level Translation Between
- 1.2-V VREF1 and 1.8-V, 2.5-V, 3.3-V, or 5-V VREF2
- 1.8-V VREF1 and 2.5-V, 3.3-V or 5-V VREF2
- 2.5-V VREF1 and 3.3-V or 5-V VREF2
- 3.3-V VREF1 and 5-V VREF2
Provides Bidirectional Voltage Translation With No Direction Pin
Low 3.5-Ω ON-State Connection Between Input and Output Ports Provides Less Signal Distortion
Open-Drain I2C I/O Ports (SCL1, SDA1, SCL2, and SDA2)
5-V Tolerant I2C I/O Ports to Support Mixed-Mode Signal Operation
High-Impedance SCL1, SDA1, SCL2, and SDA2 Pins for EN = Low
Lock-Up-Free Operation for Isolation When EN=Low
Flow-Through Pinout for Ease of Printed Circuit Board Trace Routing
Latch-Up Performance Exceeds 100 mA Per JESD 78, Class II
ESD Protection Exceeds JESD 22
- 2000-V Human-Body Model (A114-A)
- 200-V Machine Model (A115-A)
- 1000-V Charged-Device Model (C101)

下面可能是您感兴趣的TI德州仪器公司I2C特殊功能元器件

TI公司产品现货专家，订购TI公司产品不限最低起订量，TI芯片大陆现货即时发货，香港库存3-5天发货，海外库存7-10天发货

寻找全球TI代理商现货货源 - TI公司（德州仪器）电子元件在线订购