
- SNJ54HC393J - 集成电路(IC) > 逻辑 > 计数器,除法器
- MSP430FR5887IPMR - 集成电路(IC) > 嵌入式 > 微控制器
- INA819IDR - 集成电路(IC) > 线性 > 放大器 > 仪器,运算放大器,缓冲器
- MAX3222CDBRE4 - 集成电路(IC) > 接口 > 驱动器,接收器,收发器
- CD74HC175MT - 集成电路(IC) > 逻辑 > 触发器
- UCC27323DRG4 - 集成电路(IC) > 电源管理(PMIC) > 栅极驱动器
- CY74FCT374TSOCT - 集成电路(IC) > 逻辑 > 触发器
- LM358DG4 - 集成电路(IC) > 线性 > 放大器 > 仪器,运算放大器,缓冲器
- SN75157PSR - 集成电路(IC) > 接口 > 驱动器,接收器,收发器
- SN74ACT373DWR - 集成电路(IC) > 逻辑 > 锁存器
- DRV8847SEVM - 开发板,套件,编程器 > 评估板 > 评估和演示板及套件
- DS91M124TMAX - 集成电路(IC) > 接口 > 信号缓冲器、中继器、分离器
- SN74AS163NG4 - 集成电路(IC) > 逻辑 > 计数器,除法器
- DF1706E/2K - 集成电路(IC) > 音频专用
- TPUL2T123BQBR - 集成电路(IC) > 逻辑 > 多谐振荡器
- TPS70618DRVT - 集成电路(IC) > 电源管理(PMIC) > 稳压器 - 线性
- MSPM0G3519SPTR - 集成电路(IC) > 嵌入式 > 微控制器
- TLV7113025DSER - 集成电路(IC) > 电源管理(PMIC) > 稳压器 - 线性
- SN74HCT244QPWRG4Q1 - 集成电路(IC) > 逻辑 > 缓冲器,驱动器,接收器,收发器
- LMX2332LTMX/NOPB - 集成电路(IC) > 时钟/定时 > 时钟发生器,PLL,频率合成器



SE555-SP - QML V 类精密定时器
SE555-SP是TI德州仪器公司的一款无产品,SE555-SP是QML V 类精密定时器,本站介绍了SE555-SP的封装应用图解、特点和优点、功能等,并给出了与SE555-SP相关的TI元器件型号供参考。
SE555-SP - QML V 类精密定时器 - 无 - 定时器 - 德州仪器
- Timing From Microseconds to Hours
- Astable or Monostable Operation
- Adjustable Duty Cycle
- TTL-Compatible Output Can Sink or Source up to 100 mA
- QML-V Qualified, SMD 5962-98555
- Military Temperature Range (55°C to 125°C)
- Rad-Tolerant: 25 kRad (Si) TID(1)
(1) Radiation tolerance is a typical value based upon initial device qualification with dose rate = 10 mrad/sec. Radiation Lot Acceptance Testing is available - contact factory for details.
DESCRIPTION/ORDERING INFORMATION
The SE555 is a precision timing circuit capable of producing accurate time delays or oscillation. In the time-delay or monostable mode of operation, the timed interval is controlled by a single external resistor and capacitor network. In the astable mode of operation, the frequency and duty cycle can be controlled independently with two external resistors and a single external capacitor.
The threshold and trigger levels normally are two-thirds and one-third, respectively, of VCC. These levels can be altered by use of the control-voltage terminal. When the trigger input falls below the trigger level, the flip-flop is set, and the output goes high. If the trigger input is above the trigger level and the threshold input is above the threshold level, the flip-flop is reset and the output is low. The reset (RESET) input can override all other inputs and can be used to initiate a new timing cycle. When RESET goes low, the flip-flop is reset, and the output goes low. When the output is low, a low-impedance path is provided between discharge (DISCH) and ground.
The output circuit is capable of sinking or sourcing current up to 100 mA. Operation is specified for supplies of 4.5V to 16.5V. With a 5-V supply, output levels are compatible with TTL inputs.
- UCD9080 - Power Supply Sequencer and Monitor
- CSD13201W10 - N 通道 NexFET? 功率 MOSFET
- SN65ELT20 - 5 V TTL 至差动 PECL 转换器
- BQ24093 - 1A 单输入单节锂离子电池充电器,可通过 JEITA 和 100kΩ NTC 运行
- DS90LV110T - 1 至 10 LVDS 数据/时钟分配器
- ADC121S705 - 12 位、500 kSPS 至 1 MSPS、差动输入、微功耗 A/D 转换器
- SN54LS174 - 具有清零功能的六路 D 类触发器
- LMH2120 - 具有 40 dB 动态范围的 6 GHz 线性 RMS 功率检测器
- TPS7B4250-Q1 - 汽车类低压降电压跟踪低压降稳压器 (LDO)
- TPA3144D2 - 低成本 10W 无电感立体声 (BTL) D 类音频放大器



