The TPS382x family of supervisors provides circuit initialization and timing supervision, primarily for DSP and processor-based systems.

During power-on, RESET\ is asserted when supply voltage VDD becomes higher than 1.1 V. Thereafter, the supply voltage supervisor monitors VDD and keeps RESET\ active as long as VDD remains below the threshold voltage VIT–. An internal timer delays the return of the output to the inactive state (high) to ensure proper system reset. The delay time, td, starts after VDD has risen above the threshold voltage VIT–. When the supply voltage drops below the threshold voltage VIT–, the output becomes active (low) again. No external components are required. All the devices of this family have a fixed-sense threshold voltage VIT– set by an internal voltage divider.

The TPS3820/3/5/8 devices incorporate a manual reset input, MR\. A low level at MR\ causes RESET\ to become active. The TPS3824/5 devices include a high-level output RESET. TPS3820/3/4/8 have a watchdog timer that is periodically triggered by a positive or negative transition at WDI. When the supervising system fails to retrigger the watchdog circuit within the time-out interval, ttout, RESET\ becomes active for the time period td. This event also reinitializes the watchdog timer. Leaving WDI unconnected disables the watchdog.

In applications where the input to the WDI pin may be active (transitioning high and low) when the TPS3820/3/4/8 is asserting RESET\, the TPS3820/3/4/8 does not return to a non-reset state when the input voltage is above Vt. If the application requires that input to WDI is active when RESET\ is asserted, WDI must be decoupled from the active signal. This can be accomplished by using an N-channel FET in series with the WDI pin, with the gate of the FET connected to the RESET\ output as shown in Figure 1.

The product spectrum is designed for supply voltages of 2.5 V, 3 V, 3.3 V, and 5 V. The circuits are available in a 5-pin SOT23-5 package. The TPS382x-xxQ-Q1 devices are characterized for operation over a temperature range of –40°C to 125°C, and are qualified in accordance with AEC-Q100 stress test qualification for integrated circuits.

• Qualified for Automotive Applications
• ESD Protection Exceeds 2000 V Per MIL-STD-883, Method 3015; Using Human Body Model(C = 100 pF, R = 1500 )
• Power-On Reset Generator With Fixed Delay Time of 200 ms (TPS3823/4/5/8) or 25 ms (TPS3820)
• Manual Reset Input (TPS3820/3/5/8)
• Reset Output Available in Active-Low (TPS3820/3/4/5), Active-High (TPS3824) and Open-Drain (TPS3828)
• Supply Voltage Supervision Range 2.5 V, 3 V, 3.3 V, 5 V
• Watchdog Timer (TPS3820/3/4/8)
• Supply Current of 15 µA (Typ)
• SOT23-5 Package
• Applications
  • Applications Using Automotive DSPs, Microcontrollers, or Microprocessors
  • Industrial Equipment
  • Programmable Controls
  • Automotive Systems
  • Battery-Powered Equipment
  • Intelligent Instruments
  • Wireless Communications Systems

• LP3987 - 具有休眠模式的微功耗微型 SMD 150 mA 超低压降 CMOS 电压稳压器
• BQ24314C - Overvoltage & Overcurrent Protection IC & Li+ Charger Front End Protection IC
• UCC2895-Q1 - 汽车类 BiCMOS 高级相移 PWM 控制器
• UCC1801 - 低功耗 BiCMOS 电流模式 PWM
• REF3012 - 采用 SOT23-3 封装的 1.25V 输出 50ppm/℃ 漂移 50uA 静态电流的（带隙）电压参考系列
• TPL5100 - TPL5100 毫微定时器
• TPS22860 - TPS22860 超低泄漏电流负载开关
• TPS57112-Q1 - 汽车类 2.95V 至 6V 输入、2A、2MHz 同步降压 SWIFT(TM) DCDC 转换器
• DAC7564 - 12-Bit, Ultra-Low Glitch, Voltage Output DAC w/2.5V, 2ppm/°C Int Ref
• TPS62061 - 采用 2x2mm SON 封装的 3MHz、1.6A 降压转换器，Vout=1.8V