The TPS6020x step-up, regulated charge pumps generate a 3.3-V ±4% output voltage from a 1.8-V to 3.6-V input voltage. The devices are typically powered by two Alkaline, NiCd, or NiMH battery cells and operate down to a minimum supply voltage of 1.6 V. Continuous output current is a minimum of 100 mA from a 2-V input. Only four external capacitors are needed to build a complete low-ripple dc/dc converter. The push-pull operating mode of two single-ended charge pumps assures the low output voltage ripple, as current is continuously transferred to the output.

The devices operate in the newly developed LinSkip mode. In this operating mode, the device switches seamlessly from the power saving pulse-skip mode at light loads to the low-noise constant-frequency, linear-regulation mode once the output current exceeds the LinSkip threshold of about 7 mA. Even in pulse-skip mode, the output ripple is maintained at a very low level because the output resistance of the charge pump is still regulated.

Three operating modes can be programmed using the EN pin. EN = low disables the device, shuts down all internal circuits, and disconnects the output from the input. EN = high enables the device and programs it to run from the internal oscillator. The devices operate synchronized to an external clock signal if EN is clocked; thus, switching harmonics can be controlled and minimized. The devices include a low-battery detector that issues a warning if the battery voltage drops below a user-defined threshold voltage, or a power-good detector that goes active when the output voltage reaches about 90% of its nominal value.

Device options with either a low-battery or power good detector are available. This dc/dc converter requires no inductors, therefore, EMI of the system is reduced to a minimum. It is available in the small 10-pin MSOP package (DGS).

• Regulated 3.3-V Output Voltage With up to 100-mA Output Current From a 1.8-V to 3.6-V Input Voltage
• Less Than 5-mV(PP) Output Voltage Ripple Achieved With Push-Pull Topology
• Integrated Low-Battery and Power-Good Detector
• Switching Frequency Can Be Synchronized to External Clock Signal
• Extends Battery Usage With up to 90% Efficiency and 35-uA Quiescent Supply Current
• Easy-to-Design, Low Cost, Low EMI Power Supply Since No Inductors Are Used
• 0.05-uA Shutdown Current, Battery is Isolated From Load in Shutdown Mode
• Compact Converter Solution in UltraSmall 10-pin MSOP With Only Four External Capacitors Required
• Evaluation Module Available (TPS60200EVM-145)
• applications
  • Replaces DC/DC Converters With Inductors in Battery Powered Applications Like:
    • Two Battery Cells to 3.3-V Conversion
    • MP3 Portable Audio Players
    • Battery-Powered Microprocessor Systems
    • Backup-Battery Boost Converters
    • PDA's, Organizers, and Cordless Phones
    • Handheld Instrumentation
    • Glucose Meters and Other Medical Instruments

• SN74ABT16373A - 具有三态输出的 16 位透明 D 类锁存器
• TPA6203A1 - 单声道、全差动 AB 类音频放大器
• TPS3808G30 - 低静态电流可编程延迟监控电路
• SN75C185 - 低功耗多路驱动器和接收器
• SN74ALS518 - 具有使能端的八路二进制/BCD 等值比较器
• TPS51317 - 3.3V / 5V 输入、6A、D-CAP+ 模式同步降压转换器
• MSP430F67761A - MSP430F677x1A、MSP430F677x 1A、MSP430F677x1A 混合信号微控制器
• SN65HVD231Q - 汽车类 3.3V CAN 收发器
• LMH0376 - 串行数字接口
• TPS71334 - 具有集成 SVS 的双路 250mA 输出、超低噪声、高 PSRR 的低压降线性稳压器