CDC586 - 具有 1/2x、1x 及 2x 频率选项的 3.3V PLL 时钟驱动器

CDC586是TI德州仪器公司的一款无产品，CDC586是具有 1/2x、1x 及 2x 频率选项的 3.3V PLL 时钟驱动器，本站介绍了CDC586的封装应用图解、特点和优点、功能等，并给出了与CDC586相关的TI元器件型号供参考。

CDC586 - 具有 1/2x、1x 及 2x 频率选项的 3.3V PLL 时钟驱动器 - 无 - 零延迟缓冲器 - 德州仪器

产品描述

The CDC586 is a high-performance, low-skew, low-jitter clock driver. It uses a phase-lock loop (PLL) to precisely align, in both frequency and phase, the clock output signals to the clock input (CLKIN) signal. It is specifically designed for use with popular microprocessors operating at speeds from 50 MHz to 100 MHz or down to 25 MHz on outputs configured as half-frequency outputs. The CDC586 operates at 3.3-V VCC and is designed to drive a properly terminated 50- transmission line.

The feedback input (FBIN) is used to synchronize the output clocks in frequency and phase to CLKIN. One of the twelve output clocks must be fed back to FBIN for the PLL to maintain synchronization between the CLKIN input and the outputs. The output used as the feedback pin is synchronized to the same frequency as the CLKIN input.

The Y outputs can be configured to switch in phase and at the same frequency as CLKIN. Select inputs (SEL1, SEL0) configure up to nine Y outputs, in banks of three, to operate at one-half or double the CLKIN frequency, depending on which pin is fed back to FBIN (see Tables 1 and 2). All output signal duty cycles are adjusted to 50%, independent of the duty cycle at CLKIN.

Output-enable (OE\) is provided for output control. When OE\ is high, the outputs are in the high-impedance state. When OE\ is low, the outputs are active. TEST is used for factory testing of the device and can be used to bypass the PLL. TEST should be strapped to GND for normal operation.

Unlike many products containing PLLs, the CDC586 does not require external RC networks. The loop filter for the PLL is included on chip, minimizing component count, board space, and cost.

Because it is based on PLL circuitry, the CDC586 requires a stabilization time to achieve phase lock of the feedback signal to the reference signal. This stabilization time is required following power up and application of a fixed-frequency, fixed-phase signal at CLKIN, as well as following any changes to the PLL reference or feedback signals. Such changes occur upon change of the select inputs, upon enabling of the PLL via TEST, and upon enable of all outputs via OE\.

The CDC586 is characterized for operation from 0°C to 70°C.

产品特性

Low Output Skew for Clock-Distribution and Clock-Generation Applications
Operates at 3.3-V VCC
Distributes One Clock Input to Twelve Outputs
Two Select Inputs Configure Up to Nine Outputs to Operate at One-Half or Double the Input Frequency
No External RC Network Required
External Feedback Pin (FBIN) Is Used to Synchronize the Outputs to the Clock Input
Application for Synchronous DRAM, High-Speed Microprocessor
TTL-Compatible Inputs and Outputs
Outputs Drive Parallel 50- Terminated Transmission Lines
State-of-the-Art EPIC-IIB™ BiCMOS Design Significantly Reduces Power Dissipation
Distributed VCC and Ground Pins Reduce Switching Noise
Packaged in 52-Pin Thin Quad Flat Package

EPIC-IIB is a trademark of Texas Instruments Incorporated.

下面可能是您感兴趣的TI德州仪器公司无元器件

TI公司产品现货专家，订购TI公司产品不限最低起订量，TI芯片大陆现货即时发货，香港库存3-5天发货，海外库存7-10天发货

寻找全球TI代理商现货货源 - TI公司（德州仪器）电子元件在线订购